CRISTALFAB – shine restorer for marble, travertine and limestone

In stock
SKU: Cristalfab | 950 ml
Regular price €12.05
Verpakking

pH-waarde: pH 2.5 ± 0.4 (strongly acidic)

Has your marble floor lost its shine through use? CRISTALFAB from Faber Stone & Tile is a ready-to-use, water-based crystallising agent for restoring and maintaining the shine of calcareous indoor floors.

You apply the product with a single-disc machine and a suitable steel wool pad. The treatment restores the shine without yellowing, greying or an orange-peel effect.

Benefits

  • Ready to use: no dilution needed.
  • For marble, travertine and limestone indoors.
  • Easy to apply by machine via spray buffing.
  • For restoring shine and periodic shine maintenance.

Suitable surfaces

CRISTALFAB is suitable for calcareous stone such as marble, travertine and limestone. Always carry out a test first in an inconspicuous spot to assess suitability and the desired shine.

Use in brief

Clean the floor carefully and let it dry completely. Shake the container and spray a small amount onto a working area of about 1 m². Work it in immediately with a single-disc machine and steel wool pad at 150–200 revolutions per minute, until the product is dry.

After the treatment, remove the steel wool residue with a dry cloth or vacuum cleaner. The floor can then be used again.

Coverage: about 50–70 m²/kg according to Faber. Actual consumption depends on the surface and the application.

Read the full product data sheet and safety data sheet before use. Use suitable personal protective equipment.

Need advice about your floor? Contact Stone+ for help choosing and applying the right product.

Instructions for use

CRISTALFAB is ready to use. Do not dilute. For indoor use on suitable marble, travertine and limestone.

  1. Test beforehand: carry out a test in an inconspicuous spot or on a loose piece of material. Check the suitability and the shine result.
  2. Preparing the surface: carefully remove dust and dirt. Let the floor dry completely and protect adjacent surfaces. Let new adhesive and grout cure completely.
  3. Setting up the machine: use a single-disc machine of at least 1.5 HP with a suitable steel wool pad for crystallisation. Work at 150–200 revolutions per minute.
  4. Applying the product: shake well. Preferably use a bottle with a wide spray nozzle. Spray a small amount directly onto a work section of about 1 m². According to Faber, about 3–4 sprays per m².
  5. Work in immediately: spread the product immediately with even, circular movements. Keep working with the machine until the product is dry. Then treat the next work section.
  6. Repeat if necessary: on heavily worn surfaces, Faber advises a maximum of three applications per work section.
  7. Finishing: remove all steel wool residue with a dry cloth or vacuum cleaner. The floor can then be used again. Clean the tools with water afterwards.

Working conditions: surface temperature between +5 and +40 °C. Do not apply to wet or overheated surfaces.

Coverage: about 50–70 m²/kg, depending on the surface and execution.

Maintenance: use ALGAFLOOR or NEUGEL, depending on the material and following the corresponding product sheet.

Read the complete product sheet and safety data sheet before use. Wear suitable personal protection.

DANGER

  • H290: May be corrosive to metals.
  • H302: Harmful if swallowed.
  • H318: Causes serious eye damage.

Safe use

Wear tight-fitting safety goggles or face protection, suitable chemical-resistant gloves and protective work clothing. Ensure adequate ventilation and avoid breathing mist. Do not eat, drink or smoke during use. Wash hands and face thoroughly after use.

In case of contact or an accident

  • Eyes: rinse immediately with plenty of water, remove contact lenses if possible and continue rinsing. Call a Poison Centre or doctor immediately.
  • Skin: remove contaminated clothing and immediately rinse the skin with plenty of water.
  • Ingestion: call for medical help immediately. Do not induce vomiting without express medical advice.
  • Inhalation: move to fresh air and call for medical help.

Storage and environment

Store tightly closed in the original packaging, in a well-ventilated place out of direct sunlight and separated from incompatible substances. Prevent release into drains, soil and water. Absorb spilled product with inert absorbent material and dispose of product residue and contaminated packaging in accordance with the applicable regulations.

Always read the label and the complete safety data sheet before use. This text is a summary of Faber MSDS revision 10 of 14/11/2022.

GegevenWaarde en uitleg

CRISTALFAB has an acidic pH of 2.5 ± 0.4 according to Faber's technical data sheet. The product is therefore not pH-neutral.

pH value 2.5 ± 0.4

What does pH mean?
The pH indicates how acidic or alkaline an aqueous solution is. The lower the value, the more acidic the solution.

Why is Cristalfab acidic?
The formulation contains, among other things, phosphoric acid. The acidic composition suits the crystallisation treatment with which Cristalfab restores the shine of suitable calcareous stone. It is a specific treatment product, not a neutral maintenance cleaner.

Measuring conditions and sources

  • Technical data sheet, revision 6.0 of 05/06/2024: pH 2.5 ± 0.4, no concentration stated.
  • Safety data sheet, revision 10 of 14/11/2022: pH 2.1 to 2.9, at a concentration of 5%.

Always take the measuring conditions into account: the SDS value at 5% is not an instruction to dilute the product. Cristalfab is applied ready to use. Test beforehand and follow the product and safety data sheet.