STRIP 40 – Deep-acting cleaner for old wax layers and treatments

In stock
SKU: Strip 40 | 5 L
Regular price €66.00
Verpakking

pH-waarde: pH 12 (strongly alkaline)

Remove old wax layers and residue of previous treatments.
STRIP 40 from Faber Stone & Tile is a professional cleaner that loosens old residue of wax, sealers and surface treatments. This lets you clean the surface thoroughly before applying a new, suitable treatment.

The product is ready to use and suitable for both indoor and outdoor applications.

Why choose STRIP 40?

  • Powerful removal of old wax layers and treatment residue.
  • Ready to use: apply undiluted.
  • Good wetting power for even distribution.
  • Suitable for a wide range of stone-like floors.
  • Can be combined with FABER 30 2.0 for a thorough double stripping.

For which surfaces?

STRIP 40 is suitable for marble, granite, limestone, travertine, ceramic tiles, porcelain, cotto, terracotta and concrete, among others. Various composite stone materials are also among its applications.

Always carry out a test first in an inconspicuous spot to check suitability for the surface and finish.

How to use STRIP 40?

Remove loose dirt and apply the product undiluted to a dry, non-overheated surface. Spread evenly with a suitable brush or single-disc machine. Leave to act for about 10–15 minutes and work the surface in the meantime. Keep a thin layer of product present during the treatment.

Then add clean water, pick up the loosened residue and rinse thoroughly. On highly absorbent surfaces, work in areas of at most 4–5 m². Let the surface dry out completely before a new treatment.

Extra thorough cleaning with double stripping

For stubborn old layers, STRIP 40 can be combined with FABER 30 2.0, following the specific method in the product data sheet. The dosage of FABER 30 2.0 depends on the absorbency of the surface.

Product data

PropertyData
Packaging5 litres
Coverage10–20 m² per litre
UseUndiluted
Contact timeAbout 10–15 minutes
ApplicationIndoors and outdoors
ManufacturerFaber Stone & Tile
DistributorStone+

Read the full product data sheet and the safety data sheet before use. Use appropriate personal protective equipment.

Need advice about your floor or an existing treatment? Contact Stone+ for help choosing the right product.

Preparation

Remove dust and loose dirt. Work on a dry, non-overheated surface. Protect adjacent surfaces. With recently laid or grouted floors, let the adhesive and grout cure completely. Test beforehand in an inconspicuous spot.

Using STRIP 40

  1. Apply STRIP 40 undiluted . Spread evenly over the entire work area with a suitable brush or single-disc machine.
  2. Leave for about 10–15 minutes to act. Work the surface regularly in between to loosen the residue.
  3. Keep a thin layer of product present during the treatment. On absorbent surfaces, add product if necessary. On highly absorbent materials, such as terracotta, work in areas of no more than 4–5 m².
  4. Add enough clean water to emulsify the loosened residue. Spread with a brush or machine and pick up the liquid, preferably with a suitable wet vacuum.
  5. Rinse thoroughly with clean water. Repeat if necessary.

Double stripping with FABER 30 2.0

First apply STRIP 40 undiluted and leave it to act for 10–15 minutes, working it in between. Then apply FABER 30 2.0 to the same area, still covered with STRIP 40:

  • Absorbent materials, such as concrete and cotto: FABER 30 2.0 undiluted.
  • Non-absorbent materials, such as porcelain and ceramics: FABER 30 2.0 diluted to 50% in water.

Spread and work evenly. Leave to act again for about 10–15 minutes and keep a thin layer of product present. Add clean water, pick up the residue and rinse thoroughly. Test the combination and the chosen pad or brush for suitability beforehand.

After cleaning

The floor can be used again as soon as it is dry. Before a new protective treatment, let the surface dry out completely, right through. The drying time depends on the material and its absorbency.

Coverage: about 10–20 m² per litre.

Read the complete product sheet and the safety data sheet before use. Use appropriate personal protective equipment.

Read the label, the product sheet and the current safety data sheet of STRIP 40 before use. Use suitable personal protective equipment according to the safety data sheet.

• Do not apply to a wet or overheated surface.
• Protect adjacent surfaces that must not be treated.
• With recently laid or grouted surfaces, wait until adhesive and grout have fully cured.
• Test beforehand in an inconspicuous spot or on an unused piece of material.
• Only use the combination with FABER 30 2.0 according to the prescribed method, and also consult its safety data sheet.
• Store the packaging tightly closed in a cool, dry place.

These precautions do not replace the label and the official safety data sheet.

According to Faber's technical data sheet, STRIP 40 has a pH of 12 ± 0.5 and is therefore alkaline.

What does pH mean?

The pH indicates how acidic or alkaline an aqueous solution is. A neutral pH is about 7. A lower value is acidic; a higher value is alkaline.

Why does STRIP 40 have this pH?

The measured value is related to the composition of the formula. STRIP 40 was developed to loosen old wax layers, sealers and treatment residue. The solvents and the wetting action also play a role. The exact ingredients that cause the alkaline pH are not stated in the available technical data sheet.

Good to know: the pH alone does not determine whether the product is suitable for a surface. Always check the product sheet, the safety data sheet and the material suitability.

Source: Faber STRIP 40, technical data sheet Rev. 0.0 of 09/07/2026. The data sheet does not state a separate pH measuring dilution.